CNC Router Manual Processing

Manual processing refers to manipulating the machine tool directly by using the direction buttons of the three axes on the panel. http://am.co.za/ Simultaneously, the operation speed and step length etc. can be adjusted during operation according to the requirements of the operation.

After backing to the reference point, the system will enter into a manual state; http://am.co.za/ the screen display is as shown below.

AM.CO.ZA
1X 0.000 http://am.co.za/ Idle
1Y 0.000 http://am.co.za/ SOff
1Z 0.000 http://am.co.za/ Slow
Jog http://am.co.za/ 100%

Manual processing interface page

Mode Selection of Manual Processing

To satisfy the requirements of manual motion under different situations, http://am.co.za/ this system provides two kinds of manual motion modes: "Jog" and "Stepping", which can be switched by simply pressing the Shift/Auxiliary Key on CNC Router Panel button. http://am.co.za/ You can view the current motion mode through "processing mode" at the bottom of the screen.

Jog Motion Mode

There is no concrete data control under this mode. http://am.co.za/ You can press a motion direction button ( Key 6/Positive Move of X-Axis on CNC Router Panel , Key 4/Negative Move of X-Axis on CNC Router Panel , Key 8/Positive Move of Y-Axis on CNC Router Panel , Key 2/Negative Move of Y-Axis on CNC Router Panel , Key 3/Negative Move of Z-Axis on CNC Router Panel , Key 9/Positive Move of Z-Axis on CNC Router Panel ) to move the machine tool accordingly under this mode. http://am.co.za/ The machine tool will not stop until the direction button has been released. For the motion speed, it is determined by the current type of speed ( manual high speed and manual low speed ). http://am.co.za/ This motion mode is suitable for coarse tuning of the position of the mechanical coordinates.

Stepping Motion Mode

Under this motion mode, the machine tool will move accordingly after you press a motion direction button ( Key 6/Positive Move of X-Axis on CNC Router Panel , Key 4/Negative Move of X-Axis on CNC Router Panel , Key 8/Positive Move of Y-Axis on CNC Router Panel , Key 2/Negative Move of Y-Axis on CNC Router Panel , Key 3/Negative Move of Z-Axis on CNC Router Panel , Key 9/Positive Move of Z-Axis on CNC Router Panel ). http://am.co.za/ For the setup of a step, refer to "Parameter Setting" below. http://am.co.za/ This motion mode is suitable for fine tuning of the position of the mechanical coordinates.

Parameter Setting of Manual Processing

Basic parameters of manual processing include: manual high speed ( i.e. http://am.co.za/ "High" shown in the processing page ), manual low speed ( i.e. "Slow" shown in the processing page ), X\Y step and Z step.

Parameter Meaning Setting Range http://am.co.za/
MSpd (High) Two types of speed under manual processing, deciding the axis motion speed during manual processing http://am.co.za/ 0.06 ~ max. speed of machine tool
MSpd (Slow) 0.06 ~ manual high speed http://am.co.za/
Step XYZ The motion distance of the corresponding axis when a direction button of X\Y\Z is pressed once http://am.co.za/ 0.001 ~ 10000mm
The max. speed of the machine tool is related to the EasyRoute CNC Router model and has been preset at our factory. http://am.co.za/
Manual high speed and manual low speed can be switched by pressing Key 0/Speed Switchover on CNC Router Panel .
The concept of stepping ( also called as gridding with some other systems ) is introduced for the purpose of processing and debugging accuracy. http://am.co.za/ When stepping is in current manual motion mode, the step is the motion distance of the corresponding axis when a direction button of X\Y\Z is pressed once.

Under the main interface, press the Key OK/Confirmation on CNC Router Panel button to enter the parameter setting interface of manual processing, as "Manual parameter setting interface" shown below.

AM.CO.ZA
MSpd 3000/1500
StepXY 10.000
StepZ 1.000
File <No File>

Press the Key Pause/Suspend/Up on CNC Router Panel or Down Direction Key on CNC Router Panel button to select the desired parameter, and then press Key OK/Confirmation on CNC Router Panel for confirmation after modification. http://am.co.za/ Note that modification should be within the parameter range.

The current file name is displayed at the bottom of the line. http://am.co.za/ Press the Key Pause/Suspend/Up on CNC Router Panel or Down Direction Key on CNC Router Panel button to move the cursor to this line, and then press the Key OK/Confirmation on CNC Router Panel button to enter the file list of C disk ( Local Files ), as shown below. Under this interface, you can only load these files, unable to delete or copy them.

AM.CO.ZA
am-logo.g  
am-logo.dxf  
am-logo.nc  
C: [OK] Load

If there is no file in C disk, prompt "File Not Found, Show USB File?" will be displayed; http://am.co.za/ press the Key OK/Confirmation on CNC Router Panel button to enter the file list of USB flash disk.

To switch between USB file list and C file ( Local Files ) list, press Key 0/Speed Switchover on CNC Router Panel .

WCS Selection

WCS and MCS can be switched by pressing the combination button Shift/Auxiliary Key on CNC Router PanelKey 8/Positive Move of Y-Axis on CNC Router Panel . http://am.co.za/ And their screen display is as shown below. What is WCS and MCS?

AM.CO.ZA
X 0.000 Idle
Y 0.000 SOff
Z 0.000 Slow
Jog 100%
v
AM.CO.ZA
1X 0.000 Idle
1Y 0.000 SOff
1Z 0.000 Slow
Jog 100%
MCS WCS

Number 1 ~ 6 in front of X\Y\Z in WCS indicates its corresponding WCS ( G54 ~ G59 ), while there is no number before X\Y\Z in MCS. http://am.co.za/ A sign of * will appear after each axis in MCS after backing to mechanical origin has been finished.

Press the Entering Menu Page Key on CNC Router Panel button → select "3. Operations" → select "6. Select WCS", and then press the Key OK/Confirmation on CNC Router Panel button to enter its interface, http://am.co.za/ in which press the Key Pause/Suspend/Up on CNC Router Panel and Down Direction Key on CNC Router Panel buttons to select the desired WCS. http://am.co.za/ After selection, the main interface may change a little. For instance, after selecting G55 WCS, the main interface is as shown below.

AM.CO.ZA
2X 0.000 http://am.co.za/ Idle
2Y 0.000 http://am.co.za/ SOff
2Z 0.000 http://am.co.za/ Slow
Jog 100%

Main interface under G55 WCS

Further Reading..

<- Back Control Panel Manuel
for EasyRoute Series CNC Routers
<- Previous Section: Menu Items
  • Browse Files
  • Operation Options
  • Parameter Maintenance
-> Next Chapter
  • Automatic Processing

EasyRoute Series CNC Router For Sale

SKU EasyRoute CNC Router Price list,Router_3

© Bates Trust, Advanced Machinery ™
http://am.co.za/
. 2013/10/17 23:33 . [ Homepage | Price List | Visit Us ]